Maximum friction coefficient calculator for kinematic mounts — v2.0
Interfaces — geometry and stiffness
positions in m; normal and lateral stiffness in N/m
Interface
Pos X
Pos Y
Pos Z
Nor X
Nor Y
Nor Z
Free X
Free Y
Free Z
Normal stiffness
Lateral stiffness
Closing Forces
up to 6; positions in m, force in N, stiffness in N/m
Force
App X
App Y
App Z
Dir X
Dir Y
Dir Z
Magnitude
+ Friction
Lateral stiffness
Ready.
Estimated μ limit—Minimum bracketed estimate; endpoint search may miss an earlier limit.
Per-case limits
Direction
I1
I2
I3
I4
I5
I6
Red: matches the minimum to 3 significant figures; —: no bracketed limit found.
Body motion at first sliding, applied μ
relative to frictionless preload; X/Y/Z in m, Rx/Ry/Rz in rad about origin
Case
X (m)
Y (m)
Z (m)
Rx (rad)
Ry (rad)
Rz (rad)
First slip travel (m)
First sliding contact
Body displacement and rotation when the indicated support reaches first sliding. Each case starts separately from frictionless preload; unknown earlier friction history is not included. The range is max − min across the 12 endpoints, not a bound on all intermediate motion.
Normal forces at first sliding — extension
N; each interface is extended separately from frictionless preload
Case
I1
I2
I3
I4
I5
I6
Normal forces at first sliding — retraction
N; each interface is retracted separately from frictionless preload
Case
I1
I2
I3
I4
I5
I6
Fully sliding normal forces at applied μ
N; separate retraction and extension perturbation cases
Case
I1
I2
I3
I4
I5
I6
Configuration 3D View
Self-Centering of Kinematic Mounts
This tool estimates friction limits and rigid-body motion for a six-interface kinematic mount under closing forces.
Inputs
Enter interface positions and normals, closing forces, an applied friction coefficient μ, and positive normal and lateral contact stiffnesses in N/m. Closing-force contacts with friction also need positive lateral stiffness.
For a closing force with friction enabled, its direction defines the contact normal and its magnitude is treated as the normal preload. Its friction is evaluated at the applied μ and assumed to oppose the perturbation's sliding direction.
Free-sliding direction: enter a vector for a slot to remove interface friction along that axis in both directions. The vector is projected onto the contact plane. The Maxwell radial free preset makes each slot frictionless along its radial axis; it does not make the entire body free to translate radially.
Results
Estimated μ limit: a separate fully sliding model examines 12 perturbations, one in each direction at each interface, and searches for a contact-force limit. Its endpoint search may miss an earlier loss of contact or singularity.
Retraction and extension at first sliding: each support moves along its normal, separately from frictionless preload, until a contact first reaches its Coulomb friction limit. The first slip travel and body motion follow from normal and lateral stiffness and the sticking response. The force tables show normal forces at first sliding. At zero friction, sliding starts immediately. Cases where a contact opens first or no sliding onset is found are reported as unavailable.
The motion range is max − min for each component across the 12 positions at first sliding, not a bound on all intermediate or possible motion. It is unavailable if any case fails. Rotations are about the coordinate origin. Unknown previous friction history is not modeled.
Fully sliding normal forces: the separate applied μ table evaluates the original fully sliding perturbation cases; it does not represent the first-sliding calculations.
Model assumptions
The motion model assumes a rigid body, small motions, fixed contact geometry, linear contact stiffness and initially frictionless preload. Retraction and extension are independent first-sliding cases. The separate friction-limit calculation assumes fully sliding friction. Cases that cannot be solved are reported as unavailable.
Validate results independently before use in design.
CSV and 3D view
CSV exports use named columns for interface geometry and closing forces. Both these files and the earlier CSV format can be loaded.
In the 3D view, green arrows show positive contact-force directions on the body, along the entered normals. Blue arrows end at the closing-force application points. Arrow lengths scale with the greatest distance between interfaces; they indicate direction, not force magnitude or friction.
Use at own risk. Reality may differ from the model. Contact: info.omtk@gmail.com